SAVE MODE steps (step is the easiest to use)

1. pada when you can not log in, restart your computer first. 
2. When the boot process is running, you press the "F8" so it appears multiple choice 
3. pilih "save mode" and press "enter". wait a few moments to load save mode process is complete
4. tunggu some time until Windows Save Mode is displayed. 
5. setelah it, press the "Ctrl + Alt + Del" so it will display a login dialog box and password 
6. isi login and password with administrator's up to you, just the password is easily remembered by you. 
7. restartlah your computer. 
8. tekan back the "F8" then select "Start in Windows normally" and then press "enter". 
9. tekan back "Ctrl + Alt + Del" 
10. setelah show a login dialog box and password, you enter a new login and password. 
11. tekan "enter" 

aya want to share a little knowledge to you, let's together - we share the same basic sciences - basic computer ..
Between the learning phase Other: 

1. Introduction to PC 
2.  PC assembly 
3. Installation PC
4. Lan Cabling5. Network6. dl

 
1. Introduction to PC
Before Doing Assembling PC components we should recognize the past - what are the components which are In A PC
Such as: hard drive, Memory, Mother Board, VGA, FloopyDisk, CD-Room, Fans, Etc.
- Hard Disk Data Storage Is- Memory is the place Pengelolahan Data- Computer motherboard circuit board is a place to store all components- VGA output is the device that serves to change the language to display better graphics engine- Floppy disk is an additional tool to store or write data to a floppy disk or vice versa- CD - Room is the instrument used to mebaca CDs and VCDs- Power Supply is a box that is a transformer / power flow path- Fan is a device for cooling the device - there are other devices in your PC- Lancard is Perankat To A Connection With Cable
There are many devices - devices that are in PCs but to shorten the time I just explain in brief ....
 
2. PC assembly
If you are familiar with the device - any device which contained in the PC, Now Make An Assembly.Do not Fear Failure Will ... Due to Failure Is Beginning Toward SuccessWithout A lot of stale Basa Mending We Begin Aja. Babble
- Place the motherboard is most distinguished flat or above Cassing, install Proccesor On Motherboard- Replace Internal Memory At the appropriate port and should not be reversed- Prepare for Installation Cassing motherboard, install the bolts and screws on Cassing- Enter Motherboard On Cassing. Do It Slowly- Close the motherboard and insert the bolt in the hole - a hole that contained the corner - Mother sueut sehigga board meeting with Cassing- Plug connector on the Mother board power supply- Attach Expansion Slot VGA in accordance with the retaining bolts. Do it right- Pairs Lancard In reply Slot line and bolt Kecangkan- Install a hard drive on Cassing and studs with bolts (where the disk is put in front Cassing the middle)- Install CD - rangkah Cassing Room at the top (input from the front) and studs with bolts- Pairs again floopydisk (Brada place on the hard drive and align with the holes which are often used to insert the hard drive)- Passang jumper on the HDD & CD - Room, if using a cable then the HDD sbagai CDRoom sbagai master & Slave- Connect the data cable on the HDD, CD - Room, & floppy diskdrive line slots- Connect the Power Cable to the Hard Disk, CD - Room & floopydisk- To install a data cable to the motherboard you should see the user manual- If everything is selsesai, close cassingnya- Finally, attach the keyboard, mouse, monitor data cable, Power Cord, and enhancements in accordance with their port - each- Turn on the monitor and CPU, if there is 1 long beep then there are errors in installing memory- Unloading again cassingnya and pairs well - both memorynya if it is closed again cassingnya- Dinyalain try again, if a short deep sound of the computer that kmu raft has succeeded with success.</span>